128 Matches for “” AFV Vertical Axial Flow Pump 1 ps-40-3 The Flowserve AFV axial-flow, suspended-shaft vertical pump is a single stage propeller type design. This family of pumps is specifically designed for low head movement of water for a multitude of municipal, agricultural and industrial services. Flows to 180 000 m3/h (800 000 gpm) Heads to 11 m (35 ft) Speeds to 1770 rpm Sizes from 200 mm (8 in) to 3.1 m (123 in) Settings to 8 m (25 ft) AP-30 Air Piston Pump 171 pss-90-20.1 The AP-30 Air Piston Pump is a high capacity, low maintenance pump for herbicides, diesel fuel, gasoline, lubricating oil and other ag chem and industrial services. Flows to 10 m3/h (30 gpm) Uses just 15 m3/h (9 ft3/min) compressed air BSV/BCV Vertical Wet Pit, Concrete Volute Pump 6 ps-40-1 The Flowserve BSV and BCV concrete volute pumps are a vertical, wet pit design used for large flow applications requiring continuous operation. The massive concrete volute substantially reduces noise and vibration, offers high corrosion and erosion resistance, significantly increasing pump life. Flows to 115 000 m3/h (500 000 gpm) Heads to 22 m (72 ft) Byron Jackson SUBM Vertical, Deep-Well, Submersible Pump (Oil Filled Design) 116 ps-50-3b The Flowserve Byron Jackson SUBM submersible motor pump is an oil filled unit built for the most demanding deep well services. Rugged, reliable and long lasting, these units offer significant total life cycle cost savings. Flows to 4500 m3/h (19 800 gpm) Heads to 800 m (2600 ft) Motor sizes to 1500 kW (2000 hp) CAM Nuclear ASME Section III, Class 2, Between Bearing, Radially Split, Multistage, Safety Injection Pump 176 fpd-2d The Flowserve CAM high pressure safety injection pump is designed specifically for nuclear charge service. This between bearing, radially split, multistage design complies with ASME Section III, Class 2. Flows to 45 m3/h (200 gpm) Heads to 1920 m (6300 ft) Pressures to 200 bar (3000 psi) Temperatures to 120°C (250°F) CHTA Between Bearing, Radially Split, Multistage Barrel Pump 9 ps-30-12chta The Flowserve CHTA, with either a double suction or a single suction first stage impeller, is a double casing, multistage barrel pump. The CHTA is specifically designed and built for high temperature, high pressure and high flow applications, including boiler feedwater and water injection. Flows to 5225 m3/h (23 000 gpm) Heads to 4300 m (14 000 ft) Pressures to 450 bar (6600 psi) Temperatures to 250°C (480°F) Speeds to 7000 rpm CN Nuclear ASME Section III Class 3, Between Bearing, Radially Split, Diffuser Casing, Single Stage Pump 189 cn Designed specifically for nuclear reactor and steam generator feed service, The Flowserve CN pump incorporates a diffuser casing configuration. Flows to 5065 m3/h (22 300 gpm) Heads to 800 m (2630 ft) Pressures to 87 bar (1265 psi) Temperatures to 205°C (400°F) Power to 11 200 kW (15 000 hp) Speeds to 6000 rpm CPX ISO Overhung, Single Stage Process Pump 10 ps-10-30a Offering state-of-the-art hydraulics, CPX pumps are designed for applications where high performance, superior efficiency and low NPSH are required. Conforming to ISO 2858 dimensional and technical standards and to ISO 5199 design criteria, CPX pumps are found wherever reliability in severe services is a requirement. Flows to 1400 m3/h (6160 gpm) Heads to 250 m (820 ft) Pressures to 25 bar (365 psi) Temperatures from -80°C (-110°F) to 350°C (660°F) Discharge sizes from to 20 mm (0.75 in) to 200 mm (8 in) CPXM ISO Overhung, Close Coupled, Process Pump 11 ps-10-30b Offering state-of-the-art hydraulics and a compact, space saving arrangement, the CPXM pump is designed for applications where high performance, superior efficiency and low NPSH are required. Conforms to ISO 2858 dimensional and technical standards and to ISO 5199 design criteria. Flows to 570 m3/h (2500 gpm) Heads to 125 m (400 ft) Pressures to 25 bar (365 psi) Temperatures from -20°C (-5°F) to 160°C (320°F) Discharge sizes from 20 mm (0.75 in) to 150 mm (6 in) CPXP Self-Priming ISO Chemical Process Pump 174 ps-10-30cpxp Operating on the reflux priming principle, the CPXP self-priming pump offers state-of-the-art hydraulics, versatile operation and reliable performance while costing considerably less to buy, install and maintain than submersible pumps. Flows to 250 m3/h (1100 gpm) Heads to 130 m (425 ft) Pressures to 25 bar (365 psi) Temperatures from -80°C (-110°F) to 350°C (660°F) CPXR Recessed Impeller ISO Chemical Process Pump 177 ps-10-30cpxr The CPXR recessed impeller pump provides low-shear pumping of friable solids and trouble-free pumping of stringy or fibrous slurries. It combines the state-of-the-art hydraulics of the CPX with the vortex action of a recessed impeller. Flows to 750 m3/h (3300 gpm) Heads to 100 m (330 ft) Pressures to 25 bar (365 psi) Temperatures from -80°C (-110°F) to 350°C (660°F) CPXS ISO Overhung, Magnetic Drive Process Pump 16 ps-10-30f Conforming to ISO 2858 dimensional and technical standards and to ISO 5199 design criteria, the CPXS magnetic drive process pump provides leak-free pumping of hazardous, toxic, flammable, explosive, or simply valuable liquids. Flows to 420 m3/h (1850 gpm) Heads to 160 m (525 ft) Pressures to 25 bar (365 psi) Temperatures from -40°C (-40°F) to 250°C (480°F) Discharge sizes from 220 mm (0.75 in) to 100 mm (4 in) CPXV API 610 8th Edition, Overhung, Vertical Sump Pump 154 ps-10-30c Offering state-of-the-art hydraulics, CPXV API vertical sump pump was specifically engineered for the hydrocarbon and petrochemical processing industries and is compliant with API 610, 8th Edition. Flows to 1400 m3/h (6160 gpm) Heads to 250 m (820 ft) Pressures to 25 bar (365 psi) Temperatures from -40°C (-40°F) to 350°C (660°F) CPXV ISO Overhung, Vertical Sump Pump 17 ps-10-30d Offering state-of-the-art hydraulics, CPXV ISO vertical sump pump is designed for applications where high performance, superior efficiency and low NPSH are required. CPXV ISO pumps conform to ISO 5199 design criteria. Flows to 1400 m3/h (6160 gpm) Heads to 250 m (820 ft) Pressures to 25 bar (365 psi) Temperatures from -40°C (-40°F) to 350°C (660°F) CS Bewteen Bearing, Radially Split, Multistage, Ring Section Pump 18 ps-30-7 The Type CS is a radially split, multistage, ring section pump designed for high pressure services. Flows to 615 m3/h (2700 gpm) Heads to 1465 m (4800 ft) Pressures to 125 bar (1800 psi) Temperatures from -30°C (-20°F) to 165°C (330°F) CSB Multistage Diffuser Barrel Pump 19 ps-30-12csb The CSB diffuser barrel pump has become the industry benchmark in boiler feed service. An excellent choice for both combined cycle and conventional steam cycle plants, the diffuser design of the CSB provides operational stability, hydraulic flexibility and energy efficiency in medium-and heavy-duty applications. Flows to 1500 m3/h (6600 gpm) Heads to 3650 m (12 000 ft) Pressures to 300 bar (4400 psi) Temperatures to 250°C (480°F) Speeds to 6000 rpm D800 Series Cast Iron Pumps 22 d800 The D-800 line of cast iron, end suction pumps is designed to pump water and a variety of other fluids including solvents, light oils, non-corrosive chemicals, coolants and brines. Flows to 340 m3/h (1500 gpm) Heads to 120 m (400 ft) Pressures to 15 bar (220 psi) Temperatures to 120°C (250°F) DD6 Diaphragm Pump 75 dd6 The DD6 is a tough and versatile self-priming diaphragm pump designed to transfer liquids of high or low viscosity. Flows to 1.8 m3/h (8 gpm) Pressures to 1.7 bar (25 psi) Motor speeds to 2600 rpm Operating current of 12-16 amps DMX API 610 (BB3), Between Bearing, Axially Split, Multistage Pump 23 ps-30-3 The Flowserve DMX is an axially split, multistage pump designed to API 610 (BB3), latest edition. DMX pumps are particularly well suited for process charge, pipeline and injection services where uncompromising reliability over wide ranges is imperative. Flows to 2950 m3/h (13 000 gpm) Heads to 2130 m (7000 ft) Pressures to 275 bar (4000 psi) Temperatures to 200°C (400°F) Speeds to 8000 rpm Drain Titan™ Double Suction, Urethane Lined Sump Pump 4 ps-10-7b The Flowserve TKL™ Drain Titan is a double suction, urethane lined sump pump designed to provide efficient, economical and dependable service in tough wet-pit applications. Flows to 160 m3/h (700 gpm) Heads to 40 m (130 ft) Pressures to 4 bar (55 psi) Sizes from 40 mm (1.5 in) to 100 mm (4 in) Passes solids up to 15 mm (0.5 in) DSVP API 610 (OH4) Overhung, Vertical In-Line Pump 181 ps-10-27c The Flowserve DSVP pump is a fully compliant API 610 (OH4), latest edition, vertical in-line design, featuring a double suction impeller for high flow, low NPSHA booster type applications. This pump is a space and cost saving alternative to large horizontal between bearings type pumps. Flows to 3400 m3/h (15 000 gpm) Heads to 85 m (275 ft) Pressures to 40 bar (600 psi) Temperatures to 340°C (650°F) DVSH API 610 (BB1) Between Bearing Axially Split Single Stage 25 ps-20-2 The Flowserve DVSH is an axially split, double suction pump designed to API 610 (BB1), latest edition. With 94 distinct sizes, the DVSH family provides the industry's most comprehensive hydraulic coverage. Flows to 22 700 m3/h (100 000 gpm) Heads to 510 m (1500 ft) Pressures to 150 bar (2175 psi) Temperatures to 200°C (400°F) Speeds to 6000 rpm DVSR Nuclear ASME Section III Class 3, Impeller Between Bearings, Radially Split, Volute Casing, Single Stage Pump 26 fpd-2dvsr The Flowserve DVSR pump was designed specifically for nuclear reactor and steam generator feed service. This single stage, high speed pump model features a volute casing and double suction impellers. Flows to 5065 m3/h (22 300 gpm) Heads to 802 m (2630 ft) Pressures to 87 bar (1265 psi) Temperatures to 206°C (402°F) Power to 11 185 kW (15 000 hp) Speeds to 6000 rpm ERPN Overhung, Single Stage, Process Pump 27 ps-10-20a The ERPN is the pump of choice for severe chemical, petrochemical, refining and heavy-duty industrial service where full compliance with API 610 is NOT required. Flows to 1100 m3/h (4800 gpm) Heads to 230 m (755 ft) Pressures to 60 bar (870 psi) Temperatures to 350°C (650°F) ERPN-Mag Overhung, Magnetic Drive Process Pump 31 ps-10-20b The ERPN-Mag sealless process pump is the solution for applications where leak-free pumping of hazardous, toxic, explosive or valuable liquids is required. Flows to 1100 m3/h (4800 gpm) Heads to 230 m (750 ft) Working pressures to 60 bar (870 psi) Suction pressures to 50 bar (725 psi) Temperatures to 350°C (660°F) ESP2 Overhung, Vertical Immersion Sump Pump 32 ps-10-24 The ESP2 pump is a vertical immersion, open impeller type pump designed for wet pit applications in waste handling, effluent handling and liquid transfer. This rugged, single-stage pump is available in either simplex or duplex mounting configurations. Flows to 800 m3/h (3500 gpm) Heads to 90 m (300 ft) Pressures to 12 bar (175 psi) Temperatures to 180°C (350°F) F-Line Overhung, End Suction, Multistage Diffuser Pump 20 F-line The F-Line overhung, multistage, diffuser pump provides reliable operation in a variety of water applications. Flows to 500 m3/h (2200 gpm) Heads to 250 m (820 ft) Pressures to 25 bar (365 psi) Temperatures to 105°C (220°F) FRBH Overhung, Horizontal, Centerline Mounted, Heavy-Duty Paper Stock Pump 35 ps-10-16 A rugged proven performer in demanding pulp and paper mill applications, the FRBH is an overhung, horizontal, end suction, top centerline discharge design. With 19 sizes available, the high efficiency of the FRBH means reduced operating costs. Flows to 6500 m3/h (30 000 gpm) Heads to 100 m (325 ft) Temperatures to 150°C (300°F) FRBHJ Overhung, Vertical Lineshaft Sump Pump 42 ps-10-16c The FRBHJ vertical lineshaft sump pump is suitable for to handle the thick, pulpy mixtures found in the pulp and paper industry, as well as a broad range of process liquids in many other industries. Flows to 2700 m3/h (12 000 gpm) Heads to 100 m (325 ft) Temperatures to 150°C (300°F) Speeds to 1780 rpm FRBHJC Overhung, Vertical Cantilever Sump Pump 36 ps-10-16b The FRBHJC is a true stiff-shaft vertical cantilever design developed to handle the thick, pulpy mixtures found in the pulp and paper industry, as well as numerous other industries, particularly when flushing liquids are not available or cannot be tolerated. Flows to 2700 m3/h (12 000 gpm) Heads to 100 m (325 ft) Temperatures to 150°C (300°F) Speeds to 1780 rpm GAX Series Cast Iron, Double Helical, Rotary Gear Pumps 37 ps-60-2a The Flowserve GAX cast iron series, double-helical, herringbone type gear pumps are designed to handle viscous fluids at low to medium flows and pressures. These rugged pumps provide highly efficient, pulse-free pumping even under the most challenging conditions. Flows to 30 m3/h (120 gpm) Pressures to 17 bar (250 psi) Speeds to 1800 rpm Viscosities to 25 000 ssu Gearex Double Helical, Timed Rotary Gear Pump 39 ps-60-4a The Flowserve Gearex double-helical, rotary gear pump is extremely rugged and unusually compact for its high capacity and range. Timing-gear-driven herringbone rotors are precision machined for vibrationless, pulseless discharge of viscous fluids. Flows to 180 m3/h (800 gpm) Pressures to 24 bar (350 psi) Temperatures from -50°C (-60°F) to 450°C (850°F) Viscosities from 32 to 1 million ssu GR Double Helical, Rotary Gear Pump 40 ps-60-3 The Flowserve GR series, double-helical, herringbone type gear pumps have long been a workhorse of the general industry. Designed to handle viscous fluids, these rugged pumps provide high efficiency, pulse-free pumping over a wide spectrum of applications. Flows to 275 m3/h (1200 gpm) Pressures to 35 bar (500 psi) Temperatures to 350°C (650°F) Speeds to 1800 rpm Viscosities to 100 000 ssu GSX Series Stainless Steel, Double Helical, Rotary Gear Pumps 43 ps-60-2b The Flowserve GSX stainless steel series, double-helical, herringbone type gear pumps are designed to handle viscous fluids at low to medium flows and pressures. These rugged pumps provide high efficiency, pulse-free pumping even under the most challenging conditions. Flows to 30 m3/h (120 gpm) Pressures to 17 bar (250 psi) Speeds to 1800 rpm Viscosities to 25 000 ssu GT Between Bearing, Axially Split, Two Stage, Volute Pump with Semi-Centerline Support 44 gt44 The GT is an axially split, two stage, volute type ump with semi-centerline support. It is designed for a wide variety of applications. Flows to 840 m3/h (3700 gpm) Heads to 380 m (1250 ft) Pressures to 34 bar (500 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) Guardian ANSI Overhung, Magnetic Drive Pump 76 p-20-500a The Flowserve Guardian is a horizontal, magnetic drive pump, compliant with ANSI B73.1M dimensional standards. The Guardian is designed for simplicity and reliability for emission-free service requirements. The Guardian pump uses a Mark 3 casing and impeller for proven, consistent hydraulic performance. Flows to 375 m3/h (1650 gpm) Heads to 215 m (705 ft) Temperatures from -75°C (-100°F) to 290°C (550°F) HDB (HSB) Multistage, Double Suction, Dual Volute, Barrel Pump 46 ps-30-12hdb The HDB is a multistage, dual volute-type barrel pump with an axial split inner case sub-assembly and a double suction first-stage impeller. It is specifically designed for high temperature, high pressure and high flow boiler feedwater service. A single suction first stage impeller design (HSB) is also available. Flows to 4000 m3/h (17 600 gpm) Heads to 4300 m (14 000 ft) Discharge pressures to 350 bar (5100 psi) Temperatures to 250°C (480°F) Speeds to 8000 rpm HDO/HSO API 610 (BB5), Radially Split, Multistage Barrel Pumps 47 ps-30-11hdo The Flowserve HDO, with its double suction first stage impeller and the HSO, with its single suction first stage impeller, are multistage barrel pumps. They are designed for high temperature, high pressure and high flow hydrocarbon processing services. Flows to 4000 m3/h (17 600 gpm) Discharge pressures to 400 bar (5800 psi) Temperatures to 400°C (750°F) Speeds to 9000 rpm HDX API 610 (BB2), Between Bearing, Radially Split, Double Suction, Process Pump 49 ps-20-4 The HDX pump complements flow and pressure requirements between overhung and multistage process pump lines. Fully compliant with API 610 (BB2), latest edition, the HDX is engineered for safe, reliable performance at the elevated temperatures and pressures of refining and power applications. Flows to 4100 m3/h (18 000 gpm) Heads to 450 m (1500 ft) Pressures to 100 bar (1500 psi) Temperatures to 450°C (850°F) HED API 610 (BB2), Between Bearing, Radially Split, Two Stage Pump 50 ps-30-4 The Flowserve HED is a radially split, two stage pump designed to API 610 (BB2), latest edition. The HED and the HED-DS with a double suction first stage impeller are complementary to and fill the performance gap between the single stage HDX and the double casing multistage lines for high temperature services. Flows to 1000 m3/h (4400 gpm) Heads to 650 m (2100 ft) Pressures to 80 bar (1160 psi) Temperatures to 450°C (850°F) HED-DS API 610 (BB2) Between Bearing, Radially Split, Double Suction, Two Stage Pump 190 ps-30-4b The Flowserve HED-DS is a radially split, two stage pump designed to API 610 (BB2), latest edition, and with a double suction first stage impeller. Flows to 2000 m3/h (8500 gpm) Heads to 750 m (2500 ft) Pressures to 80 bar (1200 psi) Temperatures to 450°C (850°F) HP-30 and HP-55 Drum Pumps 145 hp The HP-30 and HP-55 drum pumps are designed to efficiently deliver high volumes of harsh and viscous chemicals at low pressures. HPX API 610 (OH2), Overhung Impeller, Centerline Mounted 52 ps-10-5 The Flowserve HPX pump is the workhorse of the hydrocarbon industry with unequaled versatility, reliability and safety. Fully compliant with API 610 (OH2), latest edition, this overhung impeller, centerline mounted pump offers the most comprehensive range of hydraulic coverage available in the industry. Flows to 2000 m3/h (9000 gpm) Heads to 350 m (1100 ft) Pressures to 80 bar (1160 psi) Temperatures from -160°C (-250°F) to 450°C (840°F) HPXM API 610 (OH2), Overhung Impeller, Centerline Mounted 53 pss-10-5.1 The low flow, high head design HPXM is the pump of choice for those applications outside the head-capacity range served by the HPX line. The HPXM uses custom machined, replaceable volute inserts to provide smooth, stable operation for a specific head-capacity operating point. Flows to 30 m3/h (130 gpm) Heads to 215 m (700 ft) Pressures to 80 bar (1160 psi) Temperatures from -160°C (-250°F) to 450°C (840°F) HS and YHT Multiplunger, Horizontal Reciprocating Pumps 54 ps-70-1 The Flowserve HS and YHT reciprocating pumps are horizontal multiplunger designs, engineered with a high degree of flexibility. The HS and YHT are available with multiple wet end designs and in numerous materials of construction, making them compatible with a wide variety of industrial applications. Flows to 820 m3/hr (3600 gpm) Pressures to 2050 bar (30 000 psi) Power rating to 2774 kW (3720 hp) Temperatures to 400°C (750°F) HWM API 610 (OH3), Overhung, Vertical In-Line, Low Flow Pump 58 ps-10-25a The Flowserve HWM is a space-saving, vertical in-line process pump engineered for low flow, medium to high head operation in upstream and downstream services. The HWM is fully compliant with API 610 (OH3), latest edition. Flows to 30 m3/h (130 gpm) Heads to 220 m (725 ft) Pressures to 50 bar (750 psi) Temperatures from -185°C (-300°F) to 400°C (750°F) HWM2 API 610 (OH3), Overhung, Vertical In-Line, Low Flow, Two Stage Pump 59 ps-10-25b The Flowserve HWM2 is the two stage configuration of the HWM. This space-saving, vertical in-line pump is designed for low flow, high head applications and is fully compliant with API 610 (OH3), latest edition. Flows to 30 m3/h (130 gpm) Heads to 440 m (1450 ft) Pressures to 60 bar (850 psi) Temperatures from -185°C (-300°F) to 400°C (750°F) HWX API 610 (OH3), Overhung, Vertical In-Line Pump 60 ps-10-27 The Flowserve HWX pump is a vertical, in-line design, fully compliant with API 610 (OH3), latest edition. This pump offers a space-saving alternative for many overhung process pumps in upstream and downstream services, including cryogenic, high temperature, and high working pressure services. Flows to 1500 m3/h (6600 gpm) Heads to 300 m (1000 ft) Pressures to 80 bar (1160 psi) Temperatures from -160°C (-250°F) to 400°C (750°F) Hydrex Double Helical, Rotary Gear Pump 61 hydrex The Flowserve Hydrex herringbone gear, rotary pump is a simplified but extremely reliable design for a wide variety of pumping applications. The high pressure angle and long involute profile of the precision made herringbone gear rotors eliminate root trapping, ensure smooth power transmission, and deliver quiet, efficient operation. Flows to 110 m3/h (500 gpm) Pressures to 24 bar (350 psi) Temperatures from -50°C (-60°F) to 200°C (400°F) Viscosities from 32 to 500 000 ssu LC Chemical Slurry Pump 63 ps-10-11 The LC chemical slurry pump is a horizontal, frame mounted, single stage, end suction design with a tangential discharge nozzle. It is engineered to withstand the rigor of applications that are both abrasive and corrosive. Flows to 3000 m3/h (13 200 gpm) Heads to 75 m (250 ft) Pressures to 25 bar (360 psi) Temperatures to 140°C (285°F) Specific gravities to 1.7 LLR Between Bearing, Axially Split, Two Stage, General Industry Pump 64 ps-20-3b The two stage LLR is part of a family of axially split, heavy-duty between bearing pumps that includes the horizontal, single stage LR and the vertical LRV. With thousands of units installed over the years, these pumps provide reliable and efficient performance in applications ranging from water supply to circulation duties to petroleum distribution. Flows to 295 m3/h (1300 gpm) Heads to 290 m (950 ft) Pressures to 31 bar (450 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) LNN Between Bearing, Axially Split, Single Stage Pump 68 ps-20-1 The Flowserve LNN is an axially split, double suction pump design featuring 145 impeller and volute combinations resulting in quiet operation, low NPSH requirements, and high efficiency operation in all water applications. Flows to 51 000 m3/h (225 000 gpm) Heads to 300 m (980 ft) Pressures to 30 bar (435 psi) Temperatures to 150°C (300°F) LNNC Between Bearing, Axially Split, Single Stage Pump 69 ps-20-1b The Flowserve LNNC is an axially split, double suction pump and is horizontally mounted with bottom suction and side discharge for maximum flexibility. Featuring 145 impeller and volute combinations, resulting in quiet operation, low NPSH requirements, and high efficiency operation in all water applications. Flows to 51 000 m3/h (225 000 gpm) Heads to 300 m (980 ft) Pressures to 30 bar (435 psi) Temperatures to 150°C (300°F) LNNV Between Bearing, Axially Split, Single Stage Pump 70 ps-20-1c The Flowserve LNNV is an axially split, double suction pump and is vertically mounted with in-line suction and discharge for space-saving flexibility. Featuring 145 impeller and volute combinations the LNNV provides quiet, efficient operation and low NPSH requirements in all water applications. Flows to 51 000 m3/h (225 000 gpm) Heads to 300 m (980 ft) Pressures to 30 bar (435 psi) Temperatures to 150°C (300°F) LR Between Bearing, Axially Split, Single Stage, General Industry Pump 73 ps-20-3a The single stage LR is part of a family of axially split, heavy-duty between bearing pumps that includes the vertical LRV and the two stage LLR. These pumps provide broad hydraulic coverage and low total cost of ownership. With thousands of units installed over the years, these pumps provide reliable and efficient performance in applications ranging from water supply to circulation duties to petroleum distribution. Flows to 2000 m3/h (8800 gpm) Heads to 170 m (560 ft) Pressures to 21 bar (300 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) LRV Vertical, Between Bearing, Axially Split, Single Stage, General Industry Pump 198 PS-20-3c The vertical, single stage LRV is part of a family of axially split, heavy-duty between bearing pumps that includes the horizontal, single stage LR and the two stage LLR. With thousands of units installed over the years, these pumps provide reliable and efficient performance in applications ranging from water supply to circulation duties to petroleum distribution. Flows to 2000 m3/h (8800 gpm) Heads to 137 m (450 ft) Pressures to 21 bar (300 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) M Overhung, Hard Metal, Abrasive Slurry Pump 74 ps-10-19 The Flowserve type M hard metal slurry pump is a horizontal, single stage, end suction design with a tangential discharge nozzle. The M pump is engineered to handle high concentrations of abrasive solids in suspension. Flows to 10 000 m3/h (44 000 gpm) Heads to 90 m (300 ft) Pressures to 10 bar (150 psi) Temperatures to 120°C (250°F) Solids from 2% to 70% by weight Specific gravities from 1.0 to 2.7 Medium to large sized, sharp particles Mark 3 ANSI Standard, Overhung Pump 148 p-10-500a The Flowserve Mark 3 pump is recognized as the worldwide leader in ANSI chemical process pumps. This ANSI B73.1M design offers the industry's most advanced designed features for maximum Mean Time Between Planned Maintenance (MTBPM). Flows to 1680 m3/h (7400 gpm) Heads to 215 m (700 ft) Pressures to 27 bar (400 psi) Temperatures from -75°C (-100°F) to 370°C (700°F) Mark 3 Group 4 Chemical Process Pump 8 pss-10-13.2 Designed to complement the Flowserve Mark 3 ANSI pump product line, the new Mark 3 Group 4 design offers flow rates to 4540 m3/h (20 000 US gpm), well beyond traditional ANSI sizes. Outside the scope of the ANSI performance and dimensional requirements, the Group 4 is designed for maximum reliability and efficiency in demanding applications. Flows to 4540 m3/h (20 000 gpm) Heads to 90 m (300 ft) Pressures to 14 bar (200 psi) Temperatures to 150°C (300°F) Mark 3 In-Line ANSI Standard, Overhung Pump 77 ps-10-15 The Flowserve Mark 3 In-Line pump exceeds ANSI B73.2M design criteria. This space-saving design utilizes the industry-leading Mark 3A power end and other Mark 3 advanced features for maximum Mean Time Between Planned Maintenance (MTBPM). Flows to 370 m3/h (1630 gpm) Heads to 230 m (760 ft) Pressures to 24 bar (350 psi) Temperatures from -75°C (-100°F) to 370°C (700°F) Motor sizes to 110 kW (150 hp) Mark 3 Lo-Flo, ANSI Standard Pump 78 p-10-500b The Flowserve Mark 3 Lo-Flo pump is designed to improve pump reliability at low flows and high heads. This pump conforms to ANSI B73.1M standards and is completely interchangeable with the industry leading Mark 3A power end. Flows to 50 m3/h (220 gpm) Heads to 300 m (1000 ft) Pressures to 30 bar (450 psi) Temperatures from -75°C (-100°F) to 370°C (700°F) Mark 3 Recessed Impeller Pump 81 p-10-500e The Flowserve Mark 3 Recessed Impeller pump combines the best features of the Mark 3 ANSI Standard pump with the vortex action of a recessed impeller. Pump footprint is completely interchangeable with the industry leading Mark 3A power end. Flows to 455 m3/h (2000 gpm) Heads to 120 m (400 ft) Pressures to 20 bar (285 psi) Temperatures from -75°C (-100°F) to 370°C (700°F) Mark 3 Sealmatic ANSI Standard, Overhung Pump 149 p-10-500c The Flowserve Mark 3 Sealmatic pump uses a dynamically sealing repeller to eliminate the need for mechanical seals in tough to seal services. This pump conforms to ANSI B73.1M standards and is completely interchangeable with the industry leading Mark 3A power end. Flows to 1680 m3/h (7400 gpm) Heads to 230 m (750 ft) Mark 3 Unitized Self Priming Pump 150 p-10-500d The Flowserve Mark 3 Unitized Self Primer is designed to sit high and dry at ground level and draw from liquid sources below. Pump footprint conforms to ANSI B73.1M dimensional standards and is completely interchangeable with the industry leading Mark 3A power end. Flows to 320 m3/h (1400 gpm) Heads to 120 m (400 ft) Pressures to 20 bar (285 psi) Temperatures to 370°C (700°F) Static suction lift to 6 m (20 ft) MDX/MDXN Formed Stainless Steel, Vertical Submersible, Sump Pumps 164 p-80-200 The 304L stainless steel MDX and MDXN pumps have true volutes with fewer welded parts, fewer rust points, and fewer potential leak paths because they are hydraulically formed rather than stamped. They are ideal for small sump evacuation in the home, office, farm or factory. Flows to 15 m3/h (65 gpm) Heads to 17 m (55 ft) Temperatures to 50°C (120°F) continuous; 60°C (140°F) intermittent MEN Overhung, Single Stage, End Suction, Water Pump 86 PS-10-2a The MEN single stage, end suction water pump provides reliable operation in a wide variety of applications. Flows to 700 m3/h (3080 gpm) Heads to 100 m (330 ft) Pressures to 16 bar (230 psi) Temperatures to 120°C (250°F) MF Overhung, Solids Handling Pump 87 ps-10-3 The Flowserve MF is an end-suction, side discharge, mixed flow, non-clog pump. This pump is designed specifically for reliability, low cost and long life in demanding sewage handling services or where solids in suspension are of particular concern. Flows to 2275 m3/h (10 000 gpm) Heads to 90 m (300 ft) Sizes to 400 mm (16 in) MJ Overhung, Vertical Lineshaft, Hard Metal Slurry Pump 157 ps-10-19a The type MJ hard metal, vertical lineshaft pump is designed to handle services containing coarse solids in suspension and is suitable for a broad range of wet and dry pit applications. Flows to 225 m3/h (1000 gpm) Heads to 30 m (100 ft) Pressures to 10 bar (150 psi) Temperatures to 110°C (225°F) Solids from 2% to 70% by weight Specific gravities from 1.0 to 2.7 Speeds to 1780 rpm MJC Overhung, Vertical Cantilever, Rubber Lined Slurry Pump 162 ps-10-19b The type MJC hard metal slurry pump is a true stiff-shaft cantilever design, without bottom bearings and requiring no flushing water. The MJC is particularly well suited for applications in which flushing liquids are not available or cannot be tolerated. Flows to 225 m3/h (1000 gpm) Heads to 30 m (100 ft) Pressures to 10 bar (150 psi) standard Temperatures to 110°C (225°F), depending on material Solids from 2% to 70% by weight Specific gravities from 1.0 to 2.7 Speeds to 1780 rpm MN Solids Handling, Large Capacity, Overhung Impeller 90 ps-10-4 The Flowserve MN is an end-suction, side discharge, mixed flow, non-clog pump. This large capacity pump is designed specifically for reliability, low cost and long life in demanding sewage handling services or where solids in suspension are of particular concern. Flows to 45 500 m3/h (200 000 gpm) Heads to 90 m (300 ft) Sizes to 1800 mm (72 in) MNR and MND Absorber Recirculation Pumps 185 PS-10-32 Reflecting its commitment to making flue gas desulfurization (FGD) systems more effective, Flowserve developed the rubber lined MNR and metallic MND absorber recirculation pumps. Built upon the proven design and hydraulics of the Flowserve MN solids-handling pump, the MNR and MND pumps are renown for their high efficiency and versatility. Flows to 17 500 m3/h (77 000 gpm) Heads to 40 m (130 ft) Sizes 600 mm (24 in) to 1000 mm (40 in) MPP Multiphase Screw Pump 199 FPD-3a The Flowserve MPP multiphase pump is engineered for the challenges of today's industry. It is designed for high-viscosity, high flow, low NPSH applications. Highly reliable in tough services, the MPP is able to handle slurries to 70% solids by weight and multiphase applications to 100% gas void fractions. Flows to 1520 m3/h (6700 gpm) Pressures to 100 bar (1450 psi) Temperatures from -50°C (-60°F) to 150°C (300°F) Viscosities to 200 000 000 ssu (1 million cPs) MSP Overhung, Vertical In-Line, Medium Speed Pump 93 ps-10-1 Closely following API 610, 8th Edition design criteria, the MSP is a vertical, in-line, single stage pump. Featuring a medium speed induction motor, the MSP delivers peak efficiency, excellent economy, simplified installation and reduced maintenance in low flow, high head applications. Flows to 27 m3/h (120 gpm) Heads to 600 m (1970 ft) Pressures to 100 bar (1450 psi) Maximum suction pressure to 40 bar (580 psi) Speeds from 2000 rpm to 8000 rpm Temperatures from -40°C (-40°F) to 350°C (660°F) MSP2 Overhung, Vertical In-Line, Medium Speed, Two-Stage Pump 92 ps-10-1a Closely following API 610, 8th Edition design criteria, the MSP2 is a vertical, in-line, two-stage pump. Featuring a medium speed induction motor, the MSP delivers peak efficiency, excellent economy, simplified installation and reduced maintenance. It is particularly well suited for very high head applications. Flows to 25 m3/h (110 gpm) Heads to 900 m (2955 ft) Pressures to 100 bar (1450 psi) Maximum suction pressure to 10 bar (150 psi) Temperatures from -40°C (-40°F) to 200°C (390°F) MSX Overhung, Solids Handling, Submersible Pump 94 ps-50-2 The Flowserve MSX family of solids handling, submersible pumps is engineered to perform efficiently in the most challenging environments, from pumping raw sewage to moving industrial wastewater and solids-laden liquids. Flows to 4550 m3/h (20 000 gpm) Heads to 90 m (300 ft) Sizes to 500 mm (20 in) Motor to 300 kW (400 hp) MTX/MFX Formed Stainless Steel, Submersible, Solids Handling Pumps 163 p-80-100 The 304L stainless steel MTX and MFX pumps have true volutes with fewer welded parts, fewer rust points, and fewer potential leak paths because they are hydraulically formed rather than stamped. They are ideal for moderate solids handling requirements with the benefits of submersible technology. Flows to 42 m3/h (185 gpm) Heads to 20 m (65 ft) Temperatures to 40°C (105°F) continuous; 60°C (140°F) intermittent Solids to 50 mm (2 in) diameter PH6 Panther Diaphragm Transfer Pump 172 pss-90-20.4 The PH6 Panther diaphragm pump is a non-UL rated polypropylene and Nylon transfer pump for both low and high viscosity fluids. The PH6 pump has become the standard for many ag chem mini-bulk systems. Flows to 38 l/m (10 gpm) at 16°C (60°F) Pressures to 1.7 bar (25 psi) Temperatures to 55°C (130°F) 12-volt battery operated electric motor PHL API 610 (OH2), Overhung, Centerline Mounted Pump 97 pss-10-5.2a The Flowserve PHL pump is a horizontal, overhung impeller design in full compliance with API 610 (OH2), latest edition. The PHL's 150 hydraulic configurations are supported by only four shaft and two bearing housing designs. Flows to 900 m3/h (4000 gpm) Heads to 400 m (1300 ft) Pressures to 40 bar (600 psi) Temperatures to 450°C (840°F) Motor sizes to 110 kW (150 hp) PHL-Mag API 610 (OH2), Overhung, Centerline Mounted, Magnetic Drive Pump 98 pss-10-5.2b The Flowserve PHL-MAG is the magnetic drive configuration of the PHL horizontal, overhung impeller design. Hydraulics are custom-tuned for the actual duty point by employing innovative diffuser technology. The permanent magnet drive provides 100% leak-free operation and no risk of pumped liquid contamination. Flows to 900 m3/h (4000 gpm) Heads to 400 m (1300 ft) Pressures to 40 bar (600 psi) Temperatures to 200°C (400°F) Up to 110 kW (145 hp) motor size at 3000 rpm Up to 132 kW (175 hp) motor size at 3600 rpm Pleuger SUBM Vertical Deep-Well Submersible Pump (Water Filled Design) 170 ps-50-3a The Flowserve Pleuger SUBM submersible motor pump uses water filled, wet wound motors. This design is environmentally friendly, provides high efficiency and offers great reliability. Flows to 4500 m3/h (19 800 gpm) Heads to 800 m (2600 ft) Motor sizes to 5000 kW (6700 hp) PolyChem F-Series ANSI Overhung, Non-Metallic Pump 33 p-30-500e The Flowserve PolyChem F-Series ANSI pumps are non-metallic, conventionally sealed pumps designed to meet ANSI B73.1M dimensional standards. The F-Series is designed with fiber reinforced plastic (FRP) wet ends for strength, toughness, and corrosion resistance. Flows to 110 m3/h (500 gpm) Heads to 115 m (375 ft) Pressures to 17 bar (250 psi) Temperatures from -18°C (0°F) to 107°C (225°F) PolyChem GRP ANSI B73.5M Horizontal, Engineered Polymer Composite Pump 41 ps-10-17a The PolyChem GRP pump is a single stage, end suction, centrifugal pump designed to ANSI/ASME B73.5 M Standards. With corrosion resistance superior to more expensive and highly-alloyed metals and costs closer to that of ductile iron, the PolyChem GRP pump has proven to be the low-cost, long-term solution in acidic and chloride-rich applications. Flows to 2050 m3/h (9000 gpm) Heads to 150 m (500 ft) Pressures to 17 bar (250 psi) Temperatures from -45°C (-50°F) to 120°C (250°F) PolyChem L-Series ANSI, Overhung, Non-Metallic Pump 151 p-30-500f The Flowserve PolyChem L-Series ANSI pumps are non-metallic, conventionally sealed pumps designed to meet ANSI B73.1M dimensional standards. The L-Series combines PFA lined or fiber reinforced plastic (FRP) wet ends with sophisticated mechanical seal designs that extend pump life in tough corrosives. Flows to 230 m3/h (1000 gpm) Heads to 140 m (460 ft) Pressures to 17 bar (250 psi) Temperatures from -18°C (0°F) to 150°C (300°F) PolyChem M-Series ANSI, Overhung, Non-Metallic, Magnetic Drive Pump 79 p-30-500a The Flowserve PolyChem M-Series ANSI pumps are non-metallic, magnetic drive pumps designed to meet ANSI B73.1M dimensional standards. The M-Series is designed with PFA lined wet ends for superior corrosion resistance and high temperature performance. Flows to 135 m3/h (600 gpm) Heads to 145 m (480 ft) Pressures to 17 bar (250 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) PolyChem M-Series ISO Overhung, Non-Metallic, Magnetic Drive Pump 146 p-30-500b The Flowserve PolyChem M-Series ISO pumps are non-metallic, magnetic drive pumps designed to meet ISO 2858 dimensional standards. The M-Series is designed with PFA lined wet ends for superior corrosion resistance and temperature allowance. Flows to 140 m3/h (625 gpm) - 50 Hz Heads to 95 m (310 ft) - 50 Hz Pressures to 17 bar (250 psi) Temperatures from -30°C (-20° F) to 150°C (300°F) PolyChem S-Series ANSI Overhung, Non-Metallic Pump 80 p-30-500c The Flowserve PolyChem S-Series ANSI pumps are non-metallic, conventionally sealed pumps designed to meet ANSI B73.1M dimensional standards. The S-Series is designed with PFA lined wet ends for superior corrosion resistance and temperature allowance. Flows to 420 m3/h (1860 gpm) Heads to 145 m (480 ft) Pressures to 17 bar (250 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) PolyChem S-Series ISO Overhung, Non-Metallic Pump 147 p-30-500d The Flowserve PolyChem S-Series ISO pumps are non-metallic, conventionally sealed pumps designed to meet ISO 2858 dimensional standards. The S-Series is designed with PFA lined wet ends for superior corrosion resistance and temperature allowance. Flows to 140 m3/h (625 gpm) - 50 Hz Heads to 95 m (310 ft) - 50 Hz Pressures to 17 bar (250 psi) Temperatures from -30°C (-20°F) to 150°C (300°F) PolyChem VGRP Engineered Polymer Composite Sump Pump 121 ps-10-17b The PolyChem VGRP pump is a fiberglass, vertical immersion, open impeller type pump designed for corrosive wet pit applications in waste handling and chemical transfer. The PolyChem VGRP is available in seven sizes, with single-piece columns in 3 ft to 18 ft lengths. Flows to 565 m3/h (2500 gpm) Heads to 110 m (350 ft) Pressures to 17 bar (250 psi) Temperatures from -30°C (-20°F) to 90°C (200°F) Pit depths to 4.25 m (14 ft); 6.75 m (22 ft) with optional tailpipe Primary Coolant Nuclear ASME Section III Class 1, Radially Split, Single Stage Pump 180 fpd-2 The Flowserve Nuclear Primary Coolant Pump is supplied or upgraded to rigorous technological and NSSS design standards for boiling water reactors (BWR), pressurized water reactors (PWR) and pressurized heavy water reactors (PHWR). Flows to 24 500 m3/h (108 000 gpm) Heads to 250 m (815 ft) Pressures to 170 bar (2500 psi) Temperatures to 300°C (580°F) Speeds to 1800 rpm Power rating to 9395 kW (12 600 hp) Primo-Titan Self-Priming, Solids-Handling Pump 5 ps-10-9 The Flowserve TKL Primo-Titan self-priming, solids-handling pump is engineered for reliability, low cost and long life in demanding services containing solids in suspension. Flows to 600 m3/h (2650 gpm) Heads to 35 m (115 ft) Pressures to 3.7 bar (54 psi) Temperatures to 75°C (165°F) Solids size to 75 mm (3.0 in) PVML API 610 (OH5), Overhung, Vertical In-Line Pump 100 ps-10-28a The Flowserve PVML pump is a vertical, close coupled, in-line design and is fully compliant with API 610 (OH5), latest edition. This pump offers a space-saving, alignment-free alternative for many overhung process pumps in upstream and downstream services. Flows to 500 m3/h (2200 gpm) Heads to 275 m (900 ft) Pressures to 40 bar (600 psi) Temperatures to 250°C (480°F) PVML-Mag API 685, Overhung, Vertical In-line, Magnetic Drive Pump 101 ps-10-28b The Flowserve PVML-MAG pump is the magnetic drive configuration of the close coupled, vertical in-line PVML design. Hydraulics are custom tuned to duty points using interchangeable diffuser channels. Flows to 500 m3/h (2200 gpm) Heads to 275 m (900 ft) Pressures to 40 bar (600 psi) Temperatures to 200°C (400°F) QL Vertical, Double-Suction, Twin Volute, Wet Pit Pump 102 ps-40-4 The Flowserve QL vertical, double-suction pump has a single impeller and true twin-volute design that produces more head and can operate at higher speeds than conventional, multistaged vertical turbine models. It can be used in all wet pit applications and virtually eliminates erosion and corrosion of the shaft, bearings and all internal components. Flows to 20 000 m3/h (90 000 gpm) Heads to 610 m (2000 ft) Pressures to 70 bar (1000 psi) Temperatures from -45°C (-50°F) to 200°C (400°F) Column sizes 100 mm (4 in) to 1200 mm (48 in) QMN Solids-Handling, Wet-Pit Pump 106 ps-40-5 The Flowserve QMN is a rugged wet-pit pump designed to pump sewage or for use in other wet-pit services where solids and stringy materials are present. Flows to 17 000 m3/h (75 000 gpm) Heads to 40 m (130 ft) Sizes 250 mm (10 in) to 1200 mm (48 in) Drivers to 950 kW (1250 hp) Solids up to 150 mm (6 in) R Overhung, Horizontally Split, Rubber Lined Slurry Pump 107 ps-10-18a The type R rubber lined slurry pump is a horizontal, single stage, end suction design with a tangential discharge nozzle. Engineered to handle high concentrations of fine abrasive solids in suspension or corrosive and abrasive mixtures, the type R is a workhorse in the mining and metal processing industries. Flows to 10 000 m3/h (44 000 gpm) Heads to 50 m (160 ft) Pressures to 10 bar (150 psi) standard; 35 bar (500 psi) optional Temperatures to 110°C (225°F), depending on material Solids from 2% to 70% by weight Specific gravities from 1.0 to 2.7 RJ Overhung, Vertical Lineshaft, Rubber Lined Slurry Pump 108 ps-10-18b The type RJ rubber lined, vertical lineshaft pump is designed to handle services containing fine solids in suspension and is suitable for a broad range of wet and dry pit applications. Flows to 225 m3/h (1000 gpm) Heads to 30 m (100 ft) Pressures to 10 bar (150 psi) Temperatures to 110°C (225°F), depending on material Solids from 2% to 70% by weight Specific gravities from 1.0 to 2.7 Speeds to 1780 rpm RJC Overhung, Vertical Cantilever, Rubber Lined Slurry Pump 183 ps-10-18c The type RJC rubber lined slurry pump is a true stiff-shaft cantilever design, without bottom bearings and requiring no flushing water. The RJC is particularly well suited for applications for which flushing liquids are not available or cannot be tolerated. Flows to 225 m3/h (1000 gpm) Heads to 30 m (100 ft) Pressures to 10 bar (150 psi) Temperatures to 110°C (225°F), depending on material Solids from 2% to 70% by weight Specific gravities from 1.0 to 2.7 Speeds to 1780 rpm SEM-10 and SEM-10FT Flow Meters 196 sem-10 The SEM-10 and SEM-10FT electronic flow meters offer simple one-touch operation and come ready to use. Flows from 0.5 m3/h (2 gpm) to 6.8 m3/h (30 gpm) Pressures to 4 bar (60 psi) Temperatures to 65°C (150°F) Accuracy to +/- 0.5% SEM-10SS Stainless Steel Electronic Flow Meter 130 sem-10SS The SEM-10SS electronic flow meter is a multiple use, non-commercial nutating disc flow meter with electronic LCD readout. Constructed of stainless steel and plastic, the versatile SEM-10SS can be used with many chemicals and petroleum products. Flows from 0.5 m3/h (2 gpm) to 6.8 m3/h (30 gpm) Pressures to 6.9 bar (100 psi) Temperatures to 85°C (185°F) Accuracy to +/- 0.5% SFX Formed Stainless Steel, Flanged, End Suction Pump 168 p-80-400 The 304L stainless steel SFX pump has a true volute with fewer welded parts, fewer rust points, and fewer potential leak paths because it is hydraulically formed rather than stamped. It is applied in general industrial services in which low to moderate flows are required with low to moderate heads. Flows to 85 m3/h (380 gpm) Heads to 85 m (280 ft) Sier-Bath Two Screw, Timed-Gear Rotary Pump 118 ps-60-1 Sier-Bath positive displacement timed, two screw rotary pump is the most versatile of all viscous liquid pumps. With the inherent characteristics of positive displacement, pulse-free flow and high-suction lift/self-priming capabilities, it delivers smooth, constant flow across a wide range of viscosities, temperatures and pressures. Flows to 3000 m3/h (13 200 gpm) Pressures to 240 bar (3500 psi) Temperatures to 450°C (850°F) Viscosities to 200 million ssu (40 million cps) SMP Overhung, Close Coupled, Standard Motor Pump 111 ps-10-26c The SMP standard motor pump is an overhung, end suction, close coupled, tangential discharge, frame mounted design, engineered for general industry use. Flows to 135 m3/h (600 gpm) Heads to 70 m (220 ft) Pressures to 12 bar (175 psi) Temperatures from -40°C (-40°F) to 120°C (250°F) SMX Non-Metallic, Overhung, Close Coupled, General Industry Pump 112 ps-10-26a The SMX non-metallic motor pump is an overhung, end suction, close coupled tangential discharge, frame mounted design, engineered for general industry use. Flows to 25 m3/h (100 gpm) Heads to 20 m (60 ft) Pressures to 12 bar (175 psi) Temperatures to 80°C (180°F) SPX Formed Stainless Steel, Self-Priming Pump 166 p-80-500 The 304L stainless steel SPX pump has a true volute with fewer welded parts, fewer rust points, and fewer potential leak paths because it is hydraulically formed rather than stamped. It is designed for low NPSH, low flow applications. Flows to 4 m3/h (20 gpm) Heads to 58 m (190 ft) SS6 Diaphragm Pump 82 ss6 The SS6 stainless steel, self-priming diaphragm pump is UL listed and suitable for numerous ag chem and industrial services. Flows to 2.3 m3/h (10 gpm) Operating current of 12-18 amps ST2X Formed Stainless Steel, Two-Stage, End Suction Pump 114 p-80-700 The 304L stainless steel ST2X pump has a true volute with fewer welded parts, fewer rust points, and fewer potential leak paths because it is hydraulically formed rather than stamped. It is designed for low flow, moderate head applications. Flows to 15 m3/h (65 gpm) Heads to 75 m (245 ft) STX Formed Stainless Steel, Threaded, End Suction Pump 165 p-80-600 The 304L stainless steel STX pump has a true volute with fewer welded parts, fewer rust points, and fewer potential leak paths because it is hydraulically formed rather than stamped. It is designed for low flow, low head applications. Flows to 22 m3/h (95 gpm) Heads to 45 m (145 ft) Terra-Titan™ Vertical, Cantilever Sump Pump 2 ps-10-7a The Flowserve TKL™ Terra-Titan vertical, cantilever sump pump is ruggedly built to provide the economical reliability demanded by the mining, process and general industries. Flows to 250 m3/h (1100 gpm) Heads to 45 m (150 ft) Pressures to 5 bar (70 psi) Temperatures to 100°C (212°F) Sizes from 40 mm (1.5 in) to 125 mm (5.0 in) Sump depths from 700 mm (28 in) to 1800 mm (72 in) Power range from 0.5 kW (0.75 hp) to 55 kW (75 hp) Titan™ Slurry Heavy-duty, Radially Split-case Lined Pump 3 ps-10-8 The Flowserve TKL™ Titan Slurry pump is a horizontal, single stage configuration with a radially split case and a tangential discharge. Its unique split case is designed to use either elastomeric, ceramic or hard metal liner for application flexibility. The pump is engineered to handle high concentrations of coarse, abrasive solids in suspension commonly found in mining and mineral processing. Flows to 3600 m3/h (16 000 gpm) Heads to 90 m (300 ft) Sizes from 50 mm (2 in) to 350 mm (14 in) TKW Liquid Cryogenic Turbine-Generator Expander 187 pss-50-3.1 Available in configurations up to five stages and up to 2.5 MW, the TKW turbine expander provides increased process efficiency and improved mechanical performance over other designs. From its corrosion resistant stainless steel construction to its high efficiency induction generators, the TKW offers total life cycle value. UZDL API 610 (BB1), Between Bearing, Axially Split, Two Stage Pump 119 ps-30-2 The UZDL is an axially split, two stage pump designed to API 610 (BB1), latest edition. With a double suction first-stage impeller, the UZDL pump is a natural solution for many low NPSH, high working pressure applications such as pipeline and transfer services. The pump fills the performance gap between the single stage DVS and multistage DMX pumps. Flows to 2950 m3/h (13 000 gpm) Heads to 685 m (2250 ft) Pressures to 64 bar (910 psi) Temperatures to 200°C (400°F) Speeds to 2000 rpm VCT Vertical, Mixed Flow, Wet-Pit Pump 120 ps-40-6 The Flowserve VCT is a vertical mixed flow pump designed for extended operation on condenser cooling water service, flood control or where large capacities at relatively low pressures are required and installation requirements are best suited to a vertical wet pit pump. Flows to 113 550 m3/h (500 000 gpm) Heads to 110 m (350 ft) Sizes from 500 mm (20 in) to 3000 mm (120 in) VMX Formed Stainless Steel, Vertical, Multistage Pump 167 p-80-300 The 304L stainless steel VMX pump has a true volute with fewer welded parts, fewer rust points, and fewer potential leak paths because it is hydraulically formed rather than stamped. It is designed for low flow, high head applications with the advantage of vertical in-line piping. Flows to 27 m3/h (120 gpm) Heads to 250 m (825 ft) VPC (VTP-Can) Vertical Turbine, Double Casing Pump 182 ps-40-7b Flowserve's VPC vertical turbine, double casing pump is a diffuser type, single or multistage design for services with limited NPSH available. Flows to 13 600 m3/h (60 000 gpm) Heads to 700 m (2300 ft) Pressures to 150 bar (2175 psi) Temperatures from -200°C (-330°F) to 300°C (570°F) VSMP Overhung, Vertical Cantilever, Immersion Pump 155 ps-10-26b The VSMP vertical standard motor pump is a vertical immersion centrifugal pump designed for general industry use. Flows to 135 m3/h (600 gpm) Heads to 70 m (220 ft) Pressures to 12 bar (175 psi) Temperatures from -40°C (-40°F) to 120°C (250°F) VTE, VQE, and VSE and V Series Multiplunger Vertical Reciprocating Pumps 188 ps-70-1a Flowserve's VTE, VQE, VSE and 9V Series of reciprocating pumps are vertical multiplunger types. Designed with flexibility in mind, they are available in multiple fluid-end designs and materials making them compatible with a wide variety of industrial applications. Flows to 1140 m3/h (5000 gpm) Pressures to 1035 bar (15 000 psi) Temperatures to 400°C (750°F) Power rating to 3280 kW (4400 hp) VTP Vertical Turbine, Wet Pit Pump 124 ps-40-7a Flowserve's VTP vertical turbine pump is a diffuser type, single or multiple stage design for continuous service in wet pit and deep well applications. With more than 300 bowl and impeller designs, the VTP provides unsurpassed hydraulic coverage to ensure the best pump selection for a wide variety of services. Flows to 13 600 m3/h (60 000 gpm) Heads to 700 m (2300 ft) Pressures to 150 bar (2175 psi) Temperatures from -200°C (-325°F) to 300°C (570°F) Sizes to 1375 mm (55 in) Settings to 365 m (1200 ft) W API 610 (OH4), Radially Split, Vertical In-Line, Rigid Coupled, Process Pump 127 ps-10-27b The Type W is a radially split, single stage, single suction, vertical in-line pump and is compliant with API 610 (OH4), latest edition. It is designed for continuous duty service on all process and industrial applications. Flows to 1500 m3/h (6600 gpm) Heads to 300 m (1000 ft) Pressures to 80 bar (1160 psi) Temperatures to 400°C (750°F) WD and WDX Between Bearing, Radially Split, Multistage, Ring Section Pumps 129 ps-30-5 WD and WDX are radially split, high pressure, multistage, ring section pumps designed for a wide range of process and industrial applications. Flows to 190 m3/h (800 gpm) Heads to 700 m (2300 ft) Pressures to 75 bar (1090 psi) Temperatures to 210°C (410°F) WDF Nuclear ASME Section III Class 2, Radially Split, Single Stage Pump 142 wdf Flowserve's WDF pump is used in pressurized and boiling water reactors for N Stamp safety applications. Flows to 900 m3/h (4000 gpm) Heads to 245 m (800 ft) WIK API 610 (BB5), Radially Split, Multistage Barrel Pump 131 ps-30-11b The Flowserve WIK is a multistage, barrel pump with a single stage, first stage impeller and is compliant with API 610 (BB5), latest edition. The WIK is a "special" purpose pump designed for high temperature, high pressure and high flow applications, such as decoking jet, boiler feedwater and water or brine injection. Flows to 4000 m3/h (17 600 gpm) Discharge pressures to 450 bar (6550 psi) Temperatures to 450°C (840°F) Speeds to 7600 rpm WM API 610 (OH5), Overhung, Close Coupled, Vertical In-Line, Low Flow Pump 132 ps-10-25c The Flowserve WM pump is the space-saving, close coupled configuration of the HWM pump. This pump is designed specifically for low flow, high head operation and is fully compliant with API 610 (OH5), latest edition. Flows to 30 m3/h (130 gpm) Heads to 220 m (725 ft) Pressures to 50 bar (750 psi) Temperatures from -45°C (-50°F) to 260°C (500°F) WM2 API 610 (OH5), Overhung, Close Coupled, Vertical In-Line, Low Flow, Two Stage Pump 133 ps-10-25d The Flowserve WM2 is the space-saving, close coupled configuration of the HWM2 pump. This two-stage pump is designed specifically for low flow, medium to high head operation and is fully compliant with API 610 (OH5), latest edition. Flows to 30 m3/h (130 gpm) Heads to 440 m (1450 ft) Pressures to 60 bar (850 psi) Temperatures from -45°C (-50°F) to 260°C (500°F) WNC Multistage Diffuser Barrel Pump 135 ps-30-12wnc The WNC is a diffuser-casing, high-energy, barrel pump found in power plants the world over. Highly efficient and durable, the WNC features a massive forged barrel, tandem impellers and a cartrdge-style inner casing sub-assembly. Flows to 2350 m3/h (10 300 gpm) Heads to 3800 m (12 500 ft) Pressures to 350 bar (5000 psi) Temperatures to 200°C (390°F) WUC API 610 (VS6), Vertical, Double Casing, Multistage Pump 137 ps-40-9 The Flowserve WUC vertical turbine is a radial flow or axial flow type, multistage, heavy-duty double casing pump. It is designed for continuous unspared duty in a variety of high pressure services, operating at extremes of temperature, marginal NPSHA and handling difficult liquids. Flows to 3000 m3/h (13 000 gpm) Heads to 2000 m (6500 ft) Pressures to 200 bar (3000 psi) Temperatures from -200°C (-325°F) to 350°C (660°F) WUJ API 610 (VS1), Vertical Wet Pit Pump 138 ps-40-8 The Flowserve WUJ vertical turbine is a radial flow or axial flow type, multistage, heavy-duty single casing pump. It is designed for wet pit or deep well applications. Flows to 3000 m3/h (13 000 gpm) Heads to 2000 m (6500 ft) Pressures to 200 bar (3000 psi) Temperatures from -200°C (-325°F) to 350°C (660°F) WXB Multistage, Diffuser Barrel Pump 139 ps-30-12wxb The WXB is a multistage, diffuser-casing barrel pump with tandem impellers and a balance drum to carry axial thrust forces. It is designed for users who need the hydraulic range and performance of a ring section pump, but demand the design and maintenance attributes of a barrel pump. Flows to 300 m3/h (1320 gpm) Heads to 1200 m (2175 ft) Pressures to 150 bar (2175 psi) Temperatures to 200°C (390°F) WXH Between Bearing, Radially Split, Multistage, Ring Section Pump 140 ps-30-1 The WXH pump is a horizontal, radially split, high pressure, ring section pump. It is particularly well suited for boiler feedwater on large industrial boilers and in combined cycle plants where severe cycling operation is commonplace. Flows to 1160 m3/h (5100 gpm) Heads to 2750 m (9000 ft) Pressures to 310 bar (4500 psi) Temperatures to 200°C (400°F)